Fitment

2006-2007 Honda Civic EXS 1.8L L4 1799cc

2006-2007 Honda Civic LXS 1.8L L4 1799cc

2006-2012 Honda Civic DX 1.8L L4 1799cc

2006-2012 Honda Civic GX 1.8L L4 1799cc

2006-2015 Honda Civic EX 1.8L L4 1799cc

2006-2015 Honda Civic LX 1.8L L4 1799cc

2008-2011 Honda Civic DX-G 1.8L L4 1799cc

2008-2015 Honda Civic EX-L 1.8L L4 1799cc

2009-2010 Honda Civic Sport 1.8L L4 1799cc

2009-2011 Honda Civic LX-S 1.8L L4 1799cc

2012-2013 Honda Civic HF 1.8L L4 1799cc

2013 Honda Civic Touring 1.8L L4 1799cc

2013-2015 Honda Civic Natural Gas 1.8L L4 1799cc

Are you still annoy for choosing a better CV Axle?

About our product:

• Our products are strictly producing according to the TS16949-2014 standard

?

• we invest much in the High- tech equipments, QC, and Managements.

?

• we introduced the outside of the ball cage grinding equipment, grinding ball cage device in the DOJ, VL discus type ball cage grinding equipment from Taiwan, Adopting the domestic advanced heat treatment after grinding process, the service life of such products and precision will be greatly improved.

?

• Online testing and bench test are proceeded according to the standard of GB/T10189-2014 for all the product.?

Compare to the traditional CV Axle:

1、Longer service life

Component part of inner &outer c.v.joint are under grinding after heat treatment.Especially for DOJ, DF series.

2、High standard

Our products are strictly producing according to the TS16949-2014 standard and Online testing and bench test are proceeded according to the standard of GB/T10189-2014 for all the product.

3、The increasing of strength and abrasion resistance

We use the specialized steel CF53 for c.v.joint while designing and refining the material inner organization through normalizing.

4、Clamp with high strength and anti-corrosive

The material of Clamp we choose is 1Cr13Ni9. 1cr13ni is made of martensitic stainless steel, 1 means that the carbon content is about one thousandth, which is equivalent to the carbon content of No. 10 steel, 13 means that the Cr content is about 13%, and 1 means that the nickel content is About one percent. It can be quenched to about HRC42.

5、The oil grease with excellent abrasion resistance

We use our proprietary technology in the inner structure of production to adopt special c.v.joint oil grease with anti-corrosive,could absorb the degree of -40℃ to 170℃ .

6、24hours service to help you solve all the problems during purchase and assembly.

Under the principle of 'creating the first class brand and makes value for customers', we are committed to providing customers with good service.

Ten step to replacing two CV joint axles

Step 1: This is a rear drive vehicle with two CV joint axles. Start by disconnecting the battery, jacking up the vehicle and allowing some penetrating oil to soak into any retaining bolts.

Step 2: In this case, suspension disassembly was not required. Moving brake lines and other obstacles out of the way of wrenches is a good bet before beginning.

Step 3: Loosening but not removing the strut top mounts and sway bar end link bushings can provide a bit more suspension travel for easier axle removal.

Step 4: Loosen and remove the wheel side axle mounting bolts.

Step 5: Separate the axle from the wheel. Do not allow the axle to hang from the transmission or differential. Oil seals could be damaged.

Step 6: Gently pull, pry or otherwise liberate the axle from the transmission or differential. Do not bend axle seals. Be careful not to tear the transmission or differential oil seals.

Step 7: The axle splines on the left show damage. Note the c-clip on both axles.

Step 8: Don't forget to transfer any axle seals, ABS rings or other parts to the replacement axles.

Step 9: Guide the replacement CV joint axle into place. Depending on the type of retainer, the axle should click firmly in place.

Step 10: Always use the proper torque on the axle bolts. Check axle rotation. Reassemble dismantled components.