This item is pre-owned – it will work like new once programmed to your vehicle
One (1)
Aftermarket remote keyless entry fob alarm
Transmitter control clicker keyfob controller replacement
Functions at 100% Tested & Guaranteed
Directed Electronics Inc. (DEI)
Avital
FCC ID: EZSDEI476 ( Alternate Spelling: EZSDE1476 ) Part #: 820031 Interchangeable Part #s:
LED color: Red Frequency: 433 – 434 MHz 3 buttons Battery: (1) CR 2032
|
Compatible w/ the following systems:
|
|||||||
Automate 6 7 10 25 35 410 425 435 52 53 552 553 |
Avital 2100 2200 2300 3100 3200 3300 4000 4100 4200 4300 4400 Maxx2 Maxx3 |
Hornet 533 T 554 T 740 T 742 T 851 T |
Python 400 HP 440 HP 450 ESP 460 HP 500 HP 625 HF 650 ESP 660 XP 700 900 1000 HF PC 1000 HF 1200 XP 1400 XP 1500 HF 1600 XP 2000 HF 3000 HF 3000 ESP |
Sidewinder 3000 HF 3000 ESP 3200 HS 3300 HS 3500 ESP 4500 HF 5000 HF 5000 ESP 5500 XS 6000 HF 6000 ESP 6500 HF 6500 ESP 7000 HF 7000 ESP PC 7000 SHF |
Rattler 100 110 D 200 210 D 250 259 R 300 310 D 359 R 369 D |
Valet 450 R 519 H 551 R 552 T 562 T 561 R 712 T 716 T |
Merlin 2000 |
Ungo
|
||||
Viper
|
Programming Instructions: The vehicle’s system can store up to 4 transmitters (remotes) into memory. Use the following programming routine to add transmitters to the vehicle’s security system or to change button assignments if desired. In order to enter Learn Routine, the Valet/Program push button must be plugged into the main brain's Blue 2 Pin Port (Look for a small black push button located under the drivers dash or drivers kick panel somewhere). The Valet/Program switch, plugged into the blue port, is used for programming. There is a basic sequence of steps to remember whenever programming this unit. 1) Open a door and make sure the dome light is on. 2) Turn the ignition on to the RUN position or you may also start car. 3) Within 10 seconds, press and release the Valet/Program switch the number of times that corresponds to the desired channel (listed below). Once you have selected the channel, press the switch once more and HOLD it. The LED will flash and then the horn will chirp (if connected) to confirm the selected channel. Do not release the Valet/Program switch.
4) You can advance from programming one channel to another by releasing the Valet/Programming switch and tapping it to advance channels and then HOLDING it. For instance; you have programmed Channel 1 and you want to program Channel 2. Release the Valet/Program switch. Press it one time and release it to advance from Channel 1 to Channel 2. Now, press and HOLD the Valet/Program switch. The LED will flash 2 times and the horn will chirp twice (if connected). As before, do not release. If you want to program Channel 3 after programming Channel 1, release the Valet/Program switch, press it twice and release it to advance to Channel 3. Then press it once more and HOLD it. The horn will chirp 3 times (if connected) and the LED will flash 3 times to confirm it is ready to receive the code from the transmitter. 5) Once the code(s) are learned, the Valet/Program push button can be released. 6) Programming mode will be exited if one of the following actions occurs: a. Ignition key is turned to the OFF position b. Valet/Program switch is pressed too many times. c. More than 15 seconds elapses between programming steps. The horn will emit one long chirp when programming mode has been exited.
|
Please Note: Each remote and circuit board is UV id’d prior to shipment – All returns receive a UV ID inspection to verify originality of remote sent prior to refund or replacement.
Does this keyless remote entry come with a battery?
Yes. It will have a working battery installed.
Battery Condition:
A. All remotes sold on Keyless4u include working batteries.
B. Installed batteries are not tested for battery life- they are simply working.
Some are new and some are used.
Your vehicle will be installed with one of the following keyless entry systems:
a. Standard Keyless Remote Packages: Installed at time of manufacture.
b. Optional Keyless Remote Packages: Installed by a dealer.
c. Aftermarket Keyless Remote Packages: Installed by previous owner or a car/audio shop.
d. No remote keyless entry system at all.
The above information can change
which remote you need
for your installed remote keyless system.