This Listing is For One Speaker 1x. if you want more than one we will offer discount.
PRV Audio is proud to present our MT6CX580-NDY-4 Coaxial Speaker from the MOTO Series (MT), high performance PRO audio line dedicated to motorsports installations.
This coaxial speaker is an easy fit and does not require an additional tweeter. Made from the highest quality materials and components to resist weather conditions and provide an easy and simple bolt on installation that transforms your system into the best sound reproduction available by replacing your factory speaker.
This 2-way coaxial loudspeaker established the new benchmark for vocal reproduction for outdoor applications, making it ideal for improving the sound system in your boat, UTV, 4 wheeler, Slingshot or Motorcycle.
This coaxial features a built-in horn driver with D280Ti titanium diaphragm on a 70° conical wide coverage horn waveguide.
Its horn features a screw-on design to make it easy for the speaker to be serviced. Made from the toughest PM-4 Polycarbonate high wear-resistance material to ensure long life on its treads.
It is capable of reproducing the highest frequencies at easy covering a wide range, phasing up perfect with its low frequency speaker.
This low frequency speaker can keep up with its high frequency drivers thanks to its large voice coil and extreme sensitivity of 95dB, combined with large neodymium magnets for efficient heat dissipation.
It generates an average of 130 dB of output, making it easy to match up with its high efficiency horn tweeter.
Thanks to its special spider composition, no distortion occurs at high excursion, while its silver tinsel lead wire is capable of high current, providing exceptional reliability and dynamic sound.
Reach the highest output level by following these installation recommendations for your coaxial with two amplifiers application!
Recommended HPF using PRV Digital Signal Processor DSP.
Nominal and Throat Diameter | Low Freq. 6.5″ (152 mm) | High Freq. 1″ (25.4 mm) |
Nominal impedance | 4 Ohm | 8 Ohm |
Nominal Power Handling* | 300 Watt | 40 Watt |
Continuous Program Power (RMS)** | 600 Watt | 80 Watt |
Max Peak Power*** | 1200 Watt | 160 Watt |
Sensitivity 2.00V at 1m | 95 dB | 106 dB |
Recommended Hi Pass Crossover *For Full Power Handling | 105 Hz* *12db Per Octave Crossover | 1800 Hz* *12db Per Octave Crossover |
Frequency Response | 100 – 10 kHz | 1.3 – 20 kHz |
Voice Coil Diameter | 2″ (51 mm) | 1.75″ (44 mm) |
Voice Coil Wire | CCAW | CCAW |
Voice Coil Winding Depth | 11.0 mm | N/A |
Former Material | Kapton | Kapton |
Magnetic Gap Depth | 8.0 mm | N/A |
Frame Material | Aluminum | Titanium |
Equivalent Volume | Vas | 5.77 l |
Excursion (mathematical) | Xmax*** | 3.50 mm |
Free Air Resonance | Fs | 105.9 Hz |
Mechanical Factor | Qms | 8.54 |
Electrical Factor | Qes | 0.43 |
Total Factor | Qts | 0.41 |
Cone Area | Sd | 143 cm² |
Mechanical Mass | Mms | 11.19 g |
Bl Factor | Bl | 7.16 Tm |
Dc Resistance | Re | 3.0 Ohm |
Inductance | Le | 0.178 mH at 1 kHz |
Mechanical Mass Without Air | Mmd | 10.33 g |
Mechanical Compliance | Cms | 0.202 mm/N |
***Xmax=(Voice coil winding depth-Magnetic Gap depth)/2+ Mgnetic Gap Depth/4
Overall Diameter | 6.48″ (164.5 mm) |
Front Mount Baffle Cutout | 5.62″ (143 mm) |
Mounting Depth | 3.93″ (100 mm) |
Overall Depth | 4.37″ (111 mm) |
Net Weight | 4.18 Lbs (1.9 kg) |
Shipping Weight | 4.62 Lbs (2.1 kg) |
Carton Dimensions W x L x H | 7.6″ x 7.0″ x 5.12″ (193 x 178 x 130 mm) |