Condition: AN OPEN BOX ITEM (CUSTOMER RETURN IN 100 % PERFECT CONDITION)

Warranty: 5 YEAR MANUFACTURER

Description: 

The JBL COL600 is an elegant 24-inch (600 mm) slim column loudspeaker that provides wide horizontal and narrow vertical coverage, with a built-in 10° down-tilt to the aim, providing optimum coverage for most listening areas while allowing the speaker to be installed flat to the wall. The slim, compact design—winner of international design awards for industrial design excellence—complements virtually any architectural décor.

A combination of stylish design and outstanding performance features makes the COL600 ideal for a wide variety of applications, such as conference/meeting rooms, lecture halls, retail stores, concourses, transit spaces, fill applications, audio for video, and other applications where slim, compact design and high performance is desired.

Two 5-inch x 2.25 inch racetrack woofers provide maximum radiating area in a column form factor. The tweeter is located at top of array for less obstructed coverage of the listening space and is aimed at a down angle, allowing down-tilted coverage aim, even with the cabinet flat to the wall. The shallow cabinet depth of 3.7 inches (93 mm) qualifies for ADA (Americans with Disabilities Act) projects when installed with the back of the cabinet flush to the wall.

A 20-watt multi-tap transformer allows for use on either 70V or 100V distributed speaker lines, while the speaker is switchable for direct 8-ohm operation with power handling of 80W continuous (320W peak, 2 hrs.) The 70 Hz to 20 kHz frequency range delivers clean, clear sound for music or speech.

Versatile installation is accommodated by two included L-brackets, which can be installed on either the top and bottom panels (for horizontal pan aiming) or on the left and right side panels. Both locations allow for close-to-the-wall installation. In addition, a low-profile swivel (pan) / tilt wall bracket is also included, for adding up to 10° down-tilt to the cabinet aiming (in addition to the built-in 10° down-tilt aim when the speaker is installed flat to the wall).

The COL600 has an IP54 rating (per IEC60529) for protection against ingress of dust or water. The drivers are water-treated, the grille has a water-backing, and a cover is included to protect the input terminals.

Features:

• Two 5 x 2.25 inch racetrack woofers & one 1 inch tweeter
  
• 24 inch tall with shallow 3.7 inch cabinet depth
  
• Wide 160° horizontal and focused 110° vertical coverage
  
• 10° downward tilt to aim for covering most listening areas without requiring physical down- tilting of the cabinet
  
• 80W continuous pink noise power handling (320W peak)
  
• 70 Hz – 20 kHz frequency range
  
• Built-in 20W 70V/100V multi-tap transformer, plus 8 ohm direct input.
  
• 111 dB peak SPL (105 dB continuous), 2 hrs
  
• Tweeter near top of column for unobstructed coverage of listening space
  
• Versatile mounting brackets included – both

Common Applications:

The JBL COL600 slim column loudspeaker is ideal for a wide variety of applications, such as conference/meeting rooms, lecture halls, retail stores, concourses, transit spaces, fill applications, audio for video, and other applications where slim, compact design and high performance is desired.

Specifications:

• Frequency Range (-10 dB)¹: 70 Hz – 20 kHz
  
• Frequency Response (+/-3 dB): 105 Hz – 20 kHz
  
• Power Rating (8Ω setting)2: 
  
• 160W Continuous Program (2 hrs)
  
• 80W (320W peak) Continuous Pink Noise (2 hrs)
  
• 60W (240W peak) Continuous Pink Noise (100 hrs)
  
• Sensitivity (2.83V @ 1m): 86 dB
• Color: White

Coverage Pattern:

• Vertical 110° [1kHz-4 kHz average]
  
• 10° down-tilt to aiming access for+25°/-45° coverage in relation to physical cabinet aim
  
• Horizontal 160° [1kHz – 4 kHz average]
  
• Directivity (Q): 7.8
  
• Directivity Index (DI): 8.9 dB
  
• Rated Maximum SPL: 105 dB Continuous (111 dB peak) @ 1m
  
• Nominal Impedance: 8Ω (in Thru/direct mode)
  
• Minimum Impedance: 7.0 Ω@ 275 Hz
  
• Transformer Taps: 20W, 10W, 5W @ both 70V & 100V (plus 2.5W @ 70V), and 8Ω thru, selectable via switch
  
• Transformer Insertion Loss: Less than 1 dB for all taps
  
• Maximum Input Voltage: 21 V RMS (2 hrs), 42 V peak
  
• Recommended Protective High-Pass: 70 Hz for 8 Ω operation; 60 Hz for all transformer tap settings (20W, 10W, 5W and 2.5W)
  

Drivers:

• Two 125 x 55 mm (5 x 2.25 in.) racetrack LF drivers
  
• One 25 mm (1 in.) tweeter (tweeter located at top of array for better coverage of listening space)
  
• Enclosure Material: PC + ABS, UL94-V0 flammability rating
  
• Grille: Plated SPCC with polyester powder coat finish
  
• Agency Ratings: Transformer UL recognized. RoHS, REACH compliance. LVD for CE.
  
• Environmental Rating: IP-54 rated per IEC60529, dust and water protected when installed with included rain cover for input terminal compartment and no physical up-tilt cabinet aiming. UV resistant. [Cycle 1 per ISO 4892.3-2006]
  
• Terminals: 4-pin Euroblock connection for bare wire, accepts 24 to 14 AWG gauge wire (0.25 to 2.5 sq mm). Rain cover allows for one or two 2-wire cables, with max cable jacket diameter of 8 mm (0.3 in)
  

Insert Points:

• Top & Bottom Caps: 1 threaded insert point on each cap (top & bottom, 2 insert points total) for L-BRACKETS; attach via included M6 x 28 mm bolts, flat washers, and lock washers. (Remove silicon caps over insert points AND remove pre-installed bolts holding end cap in place.) [Note: For installer-specified attachment to these threaded insert points (without L-bracket), threaded insert is M6 x 28 mm deep.]
  
• Side Panels: 1 threaded insert point on each side (left and right, for 2 insert points total) for L-BRACKETS; attach via included M6 x 28 mm bolts, flat washers, and lock washers. (Remove silicon caps over insert points.) [Note: For installer-specified attachment to these threaded insert points (without L-bracket), insert is M6 x 22 mm deep.]
  

Mounting:

• Included Swivel (Pan) / Tilt WALL BRACKET provides continuously variable ±95° degree Horizontal left-right swivel (pan) aiming (at 0° down-tilt); continuously adjustable +0°/-10° Vertical tilt (when no interference to wall); WALL and SPEAKER sections of WALL BRACKET ASSEMBLY attach together via included M6 x 12 mm bolts, flat washers, and lock washers.
  
• Two included L-brackets that can be positioned on either top & bottom insert points or side-side insert points.
  
• Top, bottom, and 2 side threaded insert points can be interfaced by installer for installer-supplied mounting methods. Installer responsible for safety of mounting method.
  
• Dimensions (H x W x D): 598 x 102 x 93 mm (23.6 x 4.1 x 3.7 inches)
  
• Net Weight: 3.5 kg (7.8 lbs) each
  
• Shipping Weight: 4.5 kg (10.0 lbs) each (packed 1 speaker per carton)
  

Included Accessories:

• Low-profile Swivel (Pan) / Tilt WALL BRACKET; 2 x L-BRACKETS that can be positioned on top/bottom or side/side insert points.

AudioSavings Return Policy:

At Audiosavings, we strongly believe in customer satisfaction and therefore offer free return shipping within 30 days of purchase on all items returned to us within the continental USA.

Prior to returning merchandise, contact us and we will give you a return authorization # and a return label.

You may return this item for a refund within 30 DAYS of purchase.

Warranty Repair/Exchange Period: 5 YEAR

If your item is defective or you want to return it for any reason within the first 30 days of when it was delivered to you; you have the following options:

• We will send you a pre-paid shipping label to replace the item for a brand new one.
• We will send you a pre-paid shipping label to exchange the item for another item of your choice. If the item you chose is more or less money we will work out the price difference with you.
• If you are returning a working item in used condition for a refund there will be a 20% used item fee deducted from your refund. All replacements and exchanges are free.

Replacement/Processing Time:

Your replacement or refund will process within 3-5 business days of when we receive the item.

Please note items with physical damage un-related to shipping are not covered under warranty. Registered software cannot be returned.

You MUST notify us within 48 hours if you receive an item that was damaged during shipping.

Process for returning items

Please email us with your eBay user ID, Item code / model #, Condition of the item, and the reason for your return. Please also indicate whether you would like a replacement, an exchange, or a refund. We will supply you with a reference number (RMA #) to put on the package which will ensure quick processing of your return. All returns require a RMA# to be returned back to our facility.