Why purchase a NEW replacement keyless entry remote transmitter?
The vehicle keyless entry remote key fob you are going to purchase from us is BRAND NEW. We seek out ONLY quality replacement remote manufacturers to ensure the key fob we sell to you is of the highest quality. Here at KeylessRemoteWarehouse we test to ensure that the shells or outer housing are made to resist cracks and breaks upon being dropped. Let?s face it; we all are going to drop our key set from time to time. We ensure that the keyless entries button pads are going to last; buying a new replacement remote control from us puts you at a longevity advantage over purchasing a used part that already has considerable wear. Even the circuit boards we choose are high quality clones with new solder joints and new resistors to ensure that they will last for the long haul. We guarantee our products are delivered to you in a ready-to-program state. We offer these car clickers at a significant cost savings to stealerships so you can keep your hard earned cash for something more fun J. Why wait? Add some convenience to your daily routine and help save the environment, order your NEW replacement car remote control today!
What are you purchasing?
This is ONE (1) NEW replacement keyless entry remote with Batteries Installed, aka "key fob" that will work with your compatible OEM (Original Equipment Manufacturer) Factory installed RKE system once successfully programmed to your vehicle.
Compatibility: Works with vehicles that use a factory keyless entry system listed in our compatibility section above AND below.
|
FCC ID#(s) |
fits GQ43VT20T |
|
Alternate Spellings |
fits GQ4-3VT20T, GQ4 3VT20T, GQ43VT20T, GQ43VT2OT, GO43VT20T, G043VT20T |
|
Part #(s) |
fits IC #: 14701-1T fits IC: 1470A-1T fits IC: 1470A1T fits MEX:RLVTR50020-562
|
|
Dealer #(s) |
fits 8974202020 89742-0202089742-AE010 fits OE# 89742-AE011, 89742AE011, 89742-AE010, 89742AE010 |
|
Compatibility |
2007 2008 2009 2010 2011 2012 Fits TOYOTA HIGHLANDER SPORT 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 Fits TOYOTA SEQUOIA 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 fits TOYOTA TUNDRA 2008 2009 2010 2011 2012 2013 2014 2015 2016 fits TOYOTA TACOMA
|
|
Button Count |
3; Lock, Unlock, Panic |
|
Battery (installed) |
1; CR2032 |
|
Frequency |
315 MHz (MHz) |
|
Programming: Please note not all customers will be able to complete the programming on their own so if you are having trouble or unsure diagnostic programming is available at your local qualified automotive locksmith or car/audio shop. |
Programming Instructions: 2008 2009 2010 2011 2012 Toyota Sequoia * 2004 2005 2006 2007 2008 2009 2010 2011 2012 Toyota Sienna * 2005 2006 2007 2008 2009 2010 2011 2012 Toyota Tacoma * __________________________________________________ 1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked. 2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out. 3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out. 4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition. 5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point. 6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons,Press C. Repeat steps A and B in step 6 for each new remote. 7. Open drivers door. Programming Instructions: 2007 2008 2009 2010 2011 2012 Toyota Highlander Base *** 2004 2005 2006 2007 2008 2009 2010 2011 2012 Toyota Tundra *** METHOD #1: 1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked. 2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out. 3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out. 4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition. 5. Within 3 seconds, the power door locks
should lock then unlock automatically 6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons, press
the lock button C. Repeat steps A and B in step 6 for each new remote. 7. Open drivers door METHOD #2: If the above programming method (#1) does
not work to sync the remote THEN What you will need: 1. Your vehicle 2. The keyless entry remote control A locksmith is least expensive As a last resort: you can visit your local car dealer for diagnostic programming. The procedure takes a few seconds to complete so many dealers
will do it as a courtesy, but please Some dealers charge for one hour labor to sync your remote with your RKE system. If your dealer does charge a fee, local locksmiths usually charge much less. |
|
Condition Notes |
|
|
|
New - ready to program to your compatible vehicle RKE system. |
Installed RKE System Type:
Please be sure you have a FACTORY (RKE) remote keyless entry system. It was not standard on all vehicles. If your current remote looks the same then this will work. Other options include: Dealer Installed or Aftermarket. The system installed in your vehicle will CHANGE the required remote. If you are unsure ask your local dealer they will need your VIN # (Vehicle Identification Number (located on our vehicle registration car, on your driver side door jam, or your windshield (lower left drives side))).
Why does your vehicles installed RKE / Security system determine which remote control your can purchase?
The remotes job is to pair with your vehicles installed RKE system. It will only sync to a matching system; therefore, you cannot purchase a different type of remote than the remote manufactured with the system. It will not pair with a foreign system.
Programming:
We will send you information on how to locate programming requirement/instructions for your make, model, and year vehicle. Some vehicles have DIY (do-it-yourself) programming instructions available. While other vehicles require diagnostic programming which is available at your local qualified automotive locksmith or dealer.
Programming Requirement Information NOTE:
The vehicle manufacturers determine the programming requirements at the time of manufacture. We pass the programming requirements / instructions on to you as a courtesy. We do not write the programming nor do we determine which vehicles require diagnostic programming and which vehicles can be programmed by the you (DIY). We are not locksmiths nor mechanics nor are we familiar with EVERY vehicles program sequence. If you have questions:
1. Check your Vehicle Owners Manual for OEM Factory remotes or The User Manual for Dealer Installed or Aftermarket RKE systems.
2. YouTube has many video postings from do-it-yourselfers to assist with all kinds of questions & most customers find if very helpful to WATCH the programming being done which can eliminate mistakes in the sequence.
To locate the programming for your vehicle via this method go to YouTube and once there in the search bar type in the following:
i. If you have a factory RKE system: your make model year + the words program remote (i.e.: 2005 Ford Mustang program remote)
ii. If you have a dealer installed or aftermarket RKE system: the FCC ID or system type + the words program remote (i.e.: ELVAT5C program remote or AS200 program transmitter?)
3. For OEM FACTORY installed systems: send us an eBay message with your vehicles make, model & year = we can pass on to you any programming information requirements we have on hand.
4. For DEALER INSTALLED RKE installed systems: send us an eBay message with your remote controls FCC ID # and PART# and the vehicles make, model, & year = we can pass on to you any programming information requirements we have on hand (the programming for dealer installed RKE systems will be different than Factory or Aftermarket installed RKE systems).
5. For AFTERMARKET INSTALLED RKE installed systems: send us an eBay message with your remote controls FCC ID # and PART# = we can pass on to you any programming information requirements we have on hand (the programming for aftermarket installed RKE systems will be different than Factory or Dealer installed RKE systems).
6. There are also many auto forums that you can go onto by just conducting a google search with your questions.
7. or a local automotive locksmith or your local parts/car/audio store will typically be able to assist you if you are trying to avoid the dealer.