Introductions:
Absorber is mainly used to suppress the shock and impact from the road after suction rebound. This Iron Shock Absorber is doing well in this field. In the most of car suspension system with shock absorbers, to accelerate the frame and body vibration attenuation, and improve the riding comfort of cars. It can also protect you safety from injured. The quality of it is very good, so you don't worry about to change it. Why not take a try for it?
Features:
1. It is made of iron material that does not contain any ordinary rubber
2. Endure high and low temperature, large temperature difference, high vacuum, strong radiation and corrosive environment.
3. High bearing capacity and the resistance to fatigue, aging, service life and long storage time.
4. Its performance index is can be designed
5. Can meet the damping, vibration, sealing, filter, throttle and acoustic noise reduction requirements
FEATURES:
- Ready To Install: The KAX complete struts assembly includes all the components required for a strut replacement in a single. No Spring Compressor Required! Save you 70% of installation time
- Recover 100% Performance: Worn out struts add 20% to the vehicle’s stopping distance. after replacing KAX struts assembly, shorten the braking distance, and increase the safety distance. Improve steering response, reduce stopping distance and give you more confidence in driving
- Increase Tire Grip: By increasing the spring stiffness coefficient, the rapid vibration of the wheel is suppressed, the tire is prevented from leaving the road, and the exercise stability is improved
- Bounce Reduction: Damping rods reduce body vibration and bounce by generating resistance through the flow of fluid to absorb or slow down the direct impact of energy
-
Feature:
Brand New
Stock parts direct replacement
Easy installation
Surface Finish: Black
Part Numbers: 172526 172527
Front Strut w/ Coil Spring Assemblies Fit For s Driver and Passenger Sides
Kit Includes:
1x Front Right Quick Install Ready Strut w/ Coil Spring - 532526 (Interchange # 172526)
1x Front Left Quick Install Ready Strut w/ Coil Spring - 532527 (Interchange # 172527)
Fit For For
MAKE MODEL YEAR RANGE SPECIFIC DETAILS
For chevrolet CAPTIVA SPORT 2012 - 2013 All Models
For chevrolet EQUINOX 2007 - 2009 Except 19" Wheels; w/o Sport Suspension
For chevrolet EQUINOX 2010 - 2017 Except 19" Wheels 2010: 2.4L
For gmc TERRAIN 2010 2.4L; Except 19" Wheels
For gmc TERRAIN 2011 - 2017 Except 19" Wheels
PONTIAC TORRENT 2007 - 2009 w/o Sport Suspension
SATURN VUE 2008 Green Line, XE, XR Models Only
SATURN VUE 2009 Hybrid, XE, XR Models Only
SATURN VUE 2010 All Models
For suzuki XL-7 2007 - 2009 All Models
Package Includes:
(As shown in the figure)
KAX complete struts assembly Features:
Upper Strut Mount: Superior premium-style bearings.SAE-grade nuts and bolts.Superior rubber-to-steel bonding.All components manufactured to meet Superior performance.
Hollow Bumper: The premium bumper prevents component damage when the suspension bottoms out.
Coil Spring: Manufactured with high-quality steel, each coil spring is precisely calibrated to support the vehicle's weight and help ensure correct ride height.
Upper Spring Seat: The upper spring seat provides consistent performance without transmitting noise or vibration into the chassis. Also supports the vehicle's weight and helps properly offset the spring in the strut tower.
Strut Dust Boot: The durable strut boot protects the strut rod and seal from dirt and debris.
Lower Spring Isolators: Prevents metal to metal contact and helps eliminate noise between the spring and spring seat.
NEW Premium Strut: Premium strut technology based on application For . Each strut features application For-engineered valving to complement each vehicle's unique ride and handling characteristics.
How to Install:
Step 1: Before You Lift the Vehicle, Loosen Lug Nuts One Full Turn.
Step 2: Jack up Vehicle and Use Jack Stands for Safety & Remove the Tire from the Rotor.
Step 3: (Wheel Alignment Is Necessary After Strut Replacement.) Marking the Position of All the Bolts Will Help Keep the Alignment Close to Original and save Time Aligning. Use a Colored Pencil to Mark the Old Strut on the Bolt.
Step 4: Use Penetrating Oil (Such As Wd40) to Coat Any Rusted Fasteners, Let Soak for Approximately 1 Hour.
Step 5: (Optional) While Waiting for Oil to Soak, Take This Time to Inspect All Other Components That May Need Replacement (Brake Pads, Rotors, Brake Hoses, Ball Joints, Cv Boots, Tie Rod Ends, Bushings, Sway Bars, Etc).
Step 6: Remove Any Brake Line or Wire Attachments from the Strut Body. Do Not Disconnect Brake Lines (If Possible)! Opening Brake Lines Will Require Bleeding of the Brake System.
Use Extreme Caution When Removing Brake Lines from Your Struts, As Any Damage to Your Brake Line Can Result in Expensive and Time Consuming Repairs.
Step 7: Remove Sway bar Attached to the Strut Assembly or Control Arm.
Step 8: Remove the Tie Rod (Only If It Attached to the Body of the Strut, If Not Leave It Attached to the Steering Knuckle).
Step 9: Remove the Strut to Knuckle Bolts at the Bottom of the Strut. on some Vehicles, the Brake Caliper and Rotor May Need to Be Removed to Gain Access.
Step 10: Remove the Upper Mounting Plate Bolts Located in the Engine or Trunk Compartment. Do Not Remove the Center Retaining Nut! It Is Not Safe to Unload the Spring from the Assembly in This Position.
Step 11: Carefully Remove the Old Strut Assembly from the Vehicle. Be Very Cautious Not to Let the Strut "Drop" down on Your Brake Line, Rotor or Drum.
Step 12: Install the New Complete Strut Assembly in the Reverse Order As Above (Steps 11-6). Using an Anti-seize Compound on All Fasteners Is Suggested.
Step 13: Carefully Double Check Your Work and Make Sure Everything Is Tightened to Manufacturers Torque Specifications.
Step 14: Replace the Tire the Rotor and Tighten to Manufacturers Torque Specifications.
Step 15: Slowly Lower the Vehicle down After Removing the Jack Stands. Pay Very Close Attention to Any Odd Sounds When the Vehicle Is Lowered Onto the New Complete Strut Assemblies.
Step 16: It Is Very Important That You Immediately "Road Test" Your Vehicle Right Away to Ensure That Installation Was Done Properly. Listen and Feel for Common Signs of Incorrect Installation While Driving Slowly over Speed Bumps, Rough Road or Potholes.
Fault inspection of shock absorber :
When the car is on a bumpy road,the shock absorber will make a "click" or "creak" sound when it is bumpy. When the car is running at a slow speed and the emergency brake is applied, if teh car vibrates violently and the shock absorber leaks oil, it indicates that the shock absorber is broken and needs to be replaced.
1、Check the appearance of the shock absorber for signs of oil leakage.You can press the four corners of the car by hand to check whether the car body bounce has abnormal sound.
2、Stop the car after driving 10 km on the road with poor conditions, and touch the shock absorber shell by hand. If the shell is hot, it means that the shock absorber is short of oil, otherwise it means that shock absorber is broken.
3、Stand at the position of the shock absorber and press the car body with force. If the car jumps on more than once or twice, it means it working well. If the car keeps nodding up and down and the car body swings up and down more than three times, the shock absorber is broken.
Hazard of broken shock absorber ⇢ DANGERS!⇢
1、If the shock absorber is not replaced due to oil leakage, the shock absorption effect of the vehicle will be reduced after long-term driving, causing the vehicle to make abnormal noise when driving to the bumpy road section, damaging the whole suspesion and causing the suspension deformation.
2、The oil leakage of shock absorber will cause uneven force on both sides of the tire, resulting in the obstruction of vehicle control, and the long time will cause the tire deviation and other faults.Finally, the cost of repairing the car will be higher than replacing a shock absorber.
3、If the broke shock absorber is not replaced for a long time, it will also affect the ride comfort, increase the driving safety risk and cause potential danger.
Important Points
➡️before Placing an Order, Be Sure to Check the Compatibility and Confirm That This Part Is Suitable for Your Vehicle.
➡️ to Confirm, Please Select a Vehicle from the "My Garage" List or Enter Your Vehicle Details Above to Ensure That Your Model Is Included in the Compatibility Table.
➡️ if You Encounter the Problem That You Can't Confirm Whether the Model Is Suitable, Please Contact Me. I Can Quickly Answer the Adaptability Problem for You. Thank You for Your Cooperation and Support!
Note
✅ Ebay Compatible List Can Not Show up All Car Model, and Sometimes It May Have Mistake, and May Not 100% Accurate or out of Date.
✅ Please Check the Manul of Your Vechicle and Choose the Correct Good.
✅ If You Are Not Sure the Which Socket Your Vehicle Need.
✅ Please Send Us Your Car Make, Model, Year and Other Information,We Will Help to Check Which You Need.
✅ If You Have Any Questions, Please Do Contact Us.thank You!